USB to USB Null Modem Rollover Cable ,PC to PC Bridge Link Comnunicate Cable
Length:1.8M
Chipset:FTDI FT232RL
The TTL Pinout:
TX-RX
RX-TX
CTS-RTS
RTS-CTS
GND-GND
The FTDI USB Null Modem Cable (NMC) solves this problem and allows a user to connect two PCs using their USB ports. The user can then perform file transfers between the PCs via the USB interface.
The NMC cable contains a small internal electronic circuit board encapsulated into the USB connector at both ends of the cable. The electronics is based on the FTDI FT232RQ USB to Serial UART IC and handles all the USB signalling and protocols. The FT232RQ datasheet, DS_FT232R, is available at https://ftdichip.com/.
The NMC cable is a USB powered, USB 2.0 full speed compatible, 2.5m cable which supports data transfer rate up to 3 Mbaud at TTL levels. The NMC cable supports the FTDIChip-ID™, with each cable end programmed with a unique USB serial number. This can be used to create security or password protected file transfer between PCs. Further information and examples on this feature are available at
https://ftdichip.com/ under FTDI Chip-ID Projects.
The cable requires USB drivers, available free from https://ftdichip.com/, which are used to make the FT232RQ within the cable ends appear as a virtual COM port (VCP). This then allows the user to communicate with the USB interface via a standard PC serial emulation port (TTY). Another FTDI USB driver, the D2XX driver, can also be used with application software to directly access the FT232RQ
Royalty free VIRTUAL COM PORT (VCP) and D2XX Direct Drivers are available for the following
Operating Systems (OS):
• Windows
• Linux
• Mac
• Android (J2xx / D2xx only)
See the following website link for the full driver support list including OS versions and legacy OS.
https://ftdichip.com/drivers/
Virtual COM Port (VCP) drivers cause the USB device to appear as an additional COM port available to the PC. Application software can access the USB device in the same way as it would access a standard COM port.
D2XX Direct Drivers allow direct access to the USB device through a DLL. Application software can access the USB device through a series of DLL function calls. The functions available are listed in the D2XX Programmer's Guide document which is available from the Documents section of our website. Please also refer to the Installation Guides webpage for details on how to install the drivers.
https://ftdichip.com/document/installation-guides/
The FTDI FT232RL Chip Features:
1. Single chip USB to asynchronous serial data transfer interface.
2. Entire USB protocol handled on the chip. No USB specific firmware programming required.
3. Fully integrated 1024 bit EEPROM storing device descriptors and CBUS I/O configuration.
4. Fully integrated USB termination resistors.
5. Fully integrated clock generation with no external crystal required plus optional clock output selection enabling a glue-less interface to external MCU or FPGA.
6. Data transfer rates from 300 baud to 3 Mbaud(RS422, RS485, RS232) at TTL levels.
7. 128 byte receive buffer and 256 byte transmit buffer utilising buffer smoothing technology to allow for high data throughput.
8. FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases.
9. Unique USB FTDIChip-ID™ feature.
10. Configurable CBUS I/O pins.
11. Transmit and receive LED drive signals.
12. UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space /no parity
13. FIFO receives and transmits buffers for high data throughput.
14. Synchronous and asynchronous bit bang interface options with RD# and WR# strobes.
15. Device supplied pre-programmed with unique USB serial number.
16. Supports bus powered, self-powered and highpower bus powered USB configurations.
17. Integrated +3.3V level converter for USB I/O.
18. Integrated level converter on UART and CBUS for interfacing to between +1.8V and +5V logic.
19. True 5V/3.3V/2.8V/1.8V CMOS drive output and TTL input.
20. Configurable I/O pin output drive strength.
21. Integrated power-on-reset circuit.
22. Fully integrated AVCC supply filtering - no external filtering required.
23. UART signal inversion option.
24. +3.3V (using external oscillator) to +5.25V (internal oscillator) Single Supply Operation.
25. Low operating and USB suspend current.
26. Low USB bandwidth consumption.
27. UHCI/OHCI/EHCI host controller compatible.
28. USB 2.0 Full Speed compatible.
29. -40°C to 85°C extended operating temperature range.
30. Available in compact Pb-free 28 Pin SSOP and QFN-32 packages (both RoHS compliant).